Matek H743-WLITE Flight Controller

Overview:

The Matek H743-WLITE Flight Controller is a flight controller focused towards fixed wing and ardupilot. It features a higher rated, higher accuracy current sensor – 220A. The FC features an DPS3010 barometer, dual switchable camera inputs and switchable 9V(12V) outputs. The H743-Wlite can run both INAV and Ardupilot.

Features:

– MCU: STM32H743VIH6, 480MHz , 512KB RAM, 2MB Flash
– IMU: ICM42688-P
– Baro: DPS310 (I2C2)
– OSD: AT7456E
– Blackbox: MicroSD card slot (SDIO)
– 7x Uarts (1,2,3,4,6,7,8) with built-in inversion.
– 13x PWM outputs(12+LED)
– 6x ADC (VBAT, Current, RSSI, Analog AirSpeed, VB2, CU2)
– 3x LEDs for FC STATUS (Blue, Red) and 3.3V indicator(Red)
– 2x I2C
– 1x CAN
– USB/Beep Extender with Type-C(USB2.0)
– Dual Camera Inputs switch
– 9V(12V) for VTX power switch
– High-precision Current Sense, 220A range
– ADC VB2 voltage divider: 1K:20K
– ADC AirSpeed voltage divider: 20K:20K

FC Firmware
– INAV: MATEKH743
– ArduPilot: MATEKH743

PDB
– Input voltage range: 6.8~30V (2~6S LiPo)
– 1x ESC power pads
– Battery Voltage divider 1K:20K (Scale 2100 in INAV,  BATT_VOLT_MULT 21.0 in ArduPilot)
– Current Senor: 220A,  3.3V ADC  (Scale 150 in INAV,  66.7 A/V in ArduPilot)
– Sense resistor: 90A continuous, 220A peak

BEC 5V output
– Designed for Flight controller, Receiver, OSD, Camera, Buzzer, 2812 LED_Strip, Buzzer, GPS module, AirSpeed
– Continuous current: 2 Amps, Max.3A

BEC 9V /12V output
– Designed for Video Transmitter, Camera, Gimbal ect.
– Continuous current: 2 Amps, Max.3A
– 12V option with Jumper pad
– for stable 9V/12V output, input voltage should > output voltage +1V

BEC Vx output
– Designed for Servos
– Voltage adjustable, 5V Default, 6V or 7.2V via jumper
– Continuous current: 8 Amps, Max.10A
– for stable Vx output, input voltage should > Vx voltage +1V

BEC 3.3V output
– Designed for Baro / Compass module and external 3.3V peripherals
– Linear Regulator
– Continuous current: 200mA

Physical
– Mounting: 25 x 25mm, Φ2mm
– Dimensions: 44 x 29 x 14.5 mm
– Weight: 22g  w/ USB/buzzer adapter

Included:
1x H743-WLITE
1x USB(Type-C)/Beep (Passive buzzer) Extender
1x 20cm JST-SH-6P to JST-SH-6P cable for USB extender.
2x 20cm JST-GH-4P to JST-GH-4P cable for CAN & I2C port
1x Rubycon ZLH 35V 470uF capacitor
Dupont 2.54 pins  (Board is shipped unsoldered)